Description

The Zeitronix Wideband Air/Fuel ratio meter and datalogging system is a high quality, stand-alone system for use with carbureted and electronic fuel injection engines. Zt-2 Wideband Kits provide the best bang for your buck delivering unmatched quality, features and capabilities for very reasonable prices.

Our system provides the accuracy of a Dyno Air/Fuel reading right in your vehicle as well as multiple engine parameters. Our base system is very easy to install which includes the wideband oxygen sensor, controller, wiring hardware, and the software required to start datalogging and tuning immediately.

??Supports Air/Fuel ratio as AFR/Lambda, plus RPM, Vacuum, Boost, Exhaust Gas Temperature, Throttle Position, 0-5 volt sensors, Air/Fluid temperature sensors and Oil/Fuel pressure sensors. Tune fuel injected and carbureted engines.

ZR-1 Gauge

Stylish, machined, black anodized aluminum bezel and slim enclosure gives the gauge an elegant appearance. High contrast LED display with three large (0.4inch / 10mm) digits. Only 3/4 inches (19mm) thick. Slim design enables unique gauge mounting options.

The Gauge works with all versions of the Zeitronix Zt-2 Wideband AFR meter and Datalogging Systems and Zt-3 Wideband AFR Meter. The ZR-1 plugs into the Zt-2 or Zt-3 DATA port and can be used while datalogging.

Clean and easy plug and play installation: power and display information is provided using one wire connecting to the Zt-2 or Zt-3 DATA port. The ZR-1 cable length is 5 ft (1.5m) and can be extended if needed.

Product Features:

Cut your tuning time in half!

The Best Wideband for your Tuning Setup

No matter if you have a stand alone engine management system, a piggy back fuel control or a carbureted engine, the ZT-2 Wideband Air Fuel Ratio Meter is a must for serious tuners! Finally you can tune for more power, closer to the edge, precisely monitoring Air/Fuel ratio Boost, EGT, RPM, throttle position and more. The Zeitronix Data Logger (ZDL) software can be utilized as a real-time display alongside the LCD Display, ZR-2 Multi-Gauge or the DashDAQ display with datalogging for up to 9 hours at a blazing rate of 65 samples per second per input.

On Board Diagnostics (OBDII) is not required but may be monitored through use of the DashDAQ II XL display which reads and clears engine error codes, logs Zt-2 Wideband data and OBDII data and has many additional performance features.

Specifications

  • Display Colour: Blue
  • 0.1 AFR accuracy
  • Operating voltage 10V to 18V
  • Switching power supply for oxygen sensor heater
  • Precise sensor temperature control
  • Reverse polarity protection
  • Integrated self-resetting fuse
  • Positive lock connectors
  • Protected inputs and outputs
  • Flexible Plug and Play Sensor Harness with a small, easy to route through the fire wall, connector
  • Wideband Oxygen Sensor included
  • Easy to install plug and play kit
  • Bosch Wideband O2 sensor Input
  • Linear Wideband Output AFR = Volts * 2 + 9.6
  • Serial data output to the Zeitronix LCD, ZR-1 AFR, and ZR-2 Multi-Gauge Displays
  • Serial data output for real time datalogging (PC laptop required)
  • RPM Input (tachometer, primary side ignition coil, crank, cam sensor).The RPM input works in any car and any ignition system. No additional adapters needed!
  • Simulated and adjustable Narrowband Output to feed a stock ECU
  • Throttle Position Sensor Input
  • Boost (MAP) Sensor Input:- 50 PSI (3.5 Bar) MAP Sensor, or 75 PSI (5.0 Bar) MAP sensor or 150 PSI (10 Bar) MAP sensor
  • Exhaust Gas Temperature (EGT) probe Input
  • User1 Input:- 0-5 volt analog input. Voltage data is viewable on all models of the LCD display. Software support for the display of Zeitronix pressure sensors.- Customized data conversions can be entered to match 0-5 volt sensor specifications. All converted User1 data values are displayed only in the software.
  • User2 Input:- 0-5 volt analog input OR configurable to be used with Fuel/Oil/Boost pressure sensors and Air/Water/Oil/Transmission temperature sensors.- Data is displayed on the 2010 Model LCD and ZR-2 Multi-gauge as a pressure or temperature.- Zeitronix Data Logger software will display and log data according to sensor type.- Customized data conversions can be entered to match 0-5 volt sensor specifications. Customized data conversion values are displayed in the Zeitronix Data Logger software only.
  • Warning Output for use with ZAVT-1 warning/trigger box
  • 5V output for sensors

What's Included

  • 1 x Zeitronix Zt-2 Wideband Controller and Datalogging System
  • 1 x Wideband Oxygen Sensor,
  • 1 x ZR-1 Gauge
  • 1 x 10ft* Sensor Harness, Signal Harness, PC Serial Cable,
  • 1 x Datalogging Software,
  • 1 x 2-Pin EGT connector to retrofit your EGT probe.
  • 1 x Installation Instructions

Compatibility

  • Universal Part

The Zeitronix Wideband Air/Fuel ratio meter and datalogging system is a high quality, stand-alone system for use with carbureted and electronic fuel injection engines. Zt-2 Wideband Kits provide the best bang for your buck delivering unmatched quality, features and capabilities for very reasonable prices.

Our system provides the accuracy of a Dyno Air/Fuel reading right in your vehicle as well as multiple engine parameters. Our base system is very easy to install which includes the wideband oxygen sensor, controller, wiring hardware, and the software required to start datalogging and tuning immediately.

??Supports Air/Fuel ratio as AFR/Lambda, plus RPM, Vacuum, Boost, Exhaust Gas Temperature, Throttle Position, 0-5 volt sensors, Air/Fluid temperature sensors and Oil/Fuel pressure sensors. Tune fuel injected and carbureted engines.

ZR-1 Gauge

Stylish, machined, black anodized aluminum bezel and slim enclosure gives the gauge an elegant appearance. High contrast LED display with three large (0.4inch / 10mm) digits. Only 3/4 inches (19mm) thick. Slim design enables unique gauge mounting options.

The Gauge works with all versions of the Zeitronix Zt-2 Wideband AFR meter and Datalogging Systems and Zt-3 Wideband AFR Meter. The ZR-1 plugs into the Zt-2 or Zt-3 DATA port and can be used while datalogging.

Clean and easy plug and play installation: power and display information is provided using one wire connecting to the Zt-2 or Zt-3 DATA port. The ZR-1 cable length is 5 ft (1.5m) and can be extended if needed.

Product Features:

Cut your tuning time in half!

The Best Wideband for your Tuning Setup

No matter if you have a stand alone engine management system, a piggy back fuel control or a carbureted engine, the ZT-2 Wideband Air Fuel Ratio Meter is a must for serious tuners! Finally you can tune for more power, closer to the edge, precisely monitoring Air/Fuel ratio Boost, EGT, RPM, throttle position and more. The Zeitronix Data Logger (ZDL) software can be utilized as a real-time display alongside the LCD Display, ZR-2 Multi-Gauge or the DashDAQ display with datalogging for up to 9 hours at a blazing rate of 65 samples per second per input.

On Board Diagnostics (OBDII) is not required but may be monitored through use of the DashDAQ II XL display which reads and clears engine error codes, logs Zt-2 Wideband data and OBDII data and has many additional performance features.

  • Display Colour: Blue
  • 0.1 AFR accuracy
  • Operating voltage 10V to 18V
  • Switching power supply for oxygen sensor heater
  • Precise sensor temperature control
  • Reverse polarity protection
  • Integrated self-resetting fuse
  • Positive lock connectors
  • Protected inputs and outputs
  • Flexible Plug and Play Sensor Harness with a small, easy to route through the fire wall, connector
  • Wideband Oxygen Sensor included
  • Easy to install plug and play kit
  • Bosch Wideband O2 sensor Input
  • Linear Wideband Output AFR = Volts * 2 + 9.6
  • Serial data output to the Zeitronix LCD, ZR-1 AFR, and ZR-2 Multi-Gauge Displays
  • Serial data output for real time datalogging (PC laptop required)
  • RPM Input (tachometer, primary side ignition coil, crank, cam sensor).The RPM input works in any car and any ignition system. No additional adapters needed!
  • Simulated and adjustable Narrowband Output to feed a stock ECU
  • Throttle Position Sensor Input
  • Boost (MAP) Sensor Input:- 50 PSI (3.5 Bar) MAP Sensor, or 75 PSI (5.0 Bar) MAP sensor or 150 PSI (10 Bar) MAP sensor
  • Exhaust Gas Temperature (EGT) probe Input
  • User1 Input:- 0-5 volt analog input. Voltage data is viewable on all models of the LCD display. Software support for the display of Zeitronix pressure sensors.- Customized data conversions can be entered to match 0-5 volt sensor specifications. All converted User1 data values are displayed only in the software.
  • User2 Input:- 0-5 volt analog input OR configurable to be used with Fuel/Oil/Boost pressure sensors and Air/Water/Oil/Transmission temperature sensors.- Data is displayed on the 2010 Model LCD and ZR-2 Multi-gauge as a pressure or temperature.- Zeitronix Data Logger software will display and log data according to sensor type.- Customized data conversions can be entered to match 0-5 volt sensor specifications. Customized data conversion values are displayed in the Zeitronix Data Logger software only.
  • Warning Output for use with ZAVT-1 warning/trigger box
  • 5V output for sensors
  • 1 x Zeitronix Zt-2 Wideband Controller and Datalogging System
  • 1 x Wideband Oxygen Sensor,
  • 1 x ZR-1 Gauge
  • 1 x 10ft* Sensor Harness, Signal Harness, PC Serial Cable,
  • 1 x Datalogging Software,
  • 1 x 2-Pin EGT connector to retrofit your EGT probe.
  • 1 x Installation Instructions
  • Universal Part

Best Sellers